mdpna-465

    Sorry
    I do not know who to ask about my problem
    mdpna-465 with lower overhead bar reinstalled with the wrong ROM
    Now it's dead does not come on screen, no PC connection
    There are power buttons work
    With 9 pin of flash is not starting
    I have the original ROM
    Please if you can help with ideas, photos, instructions
    I can not get him to the world, Booth
    pp sorry for bad english
    :017::017:

    OK, at first your PNA doesn't have a contactbar, right? Are you sure you took the correct ROM for flashing your PNA -> R15?


    EDIT: or, if your PNA looks like this one -> PNA470 you have to flash with R22.



    And after flashing you've to reinstall the (new) GoPal-SW.



    yes i have


    Photo 2 is bottom connector
    reinstall it with a ROM of 510 and has finished reinstalling, died
    now I have prepared ROM 465t but I can not get him to leave
    this is my problem

    Einmal editiert, zuletzt von helpos ()

    ?


    Does the bottom of your device look like picture one or two?

    Photo 2 is bottom connector
    device is "BLUEMEDIA-BM6600" FULL analogue mdpna465t
    the board wrote PWA-MDPNA470T_MAIN_BD
    PCB: 316162300005_R02
    to replace flash memory, or some secret way to go?

    Zitat von helpos

    when connecting usb cable LED lights and really charge the battery
    Pressing the power after 2-3 seconds coming PSUs 3.3 volts and 1.7 volts for the CPU but display no lights and no connection to PC



    Whats happenning when you press both buttons on the right side.. (if there are two buttons present)
    Does your device look like:
    [Blockierte Grafik: http://bilder4.preissuchmaschine.de/prodfoto/bluemediabm6600.jpg]
    ?


    By the way: do you have a GoPal Software for the installation after flashing?

    any button to push "power, poi, reset" or three buttons, only includes the supply and ..... nothing happens, screen does not light
    I need a blue screen "bootloader" then I know what to do
    just hurry and messed ROM files
    then I can put whatever I want navigation software
    help boot rom
    YES i have this ROM http://www.gopal-navigator.de/downloads.php?do=file&id=302

    2 Mal editiert, zuletzt von helpos ()

    There is only one way to enter the boot-menue.
    Hold the Power and only the power button on hold until the blue LED blinks up for one time - than it is really OFF.


    Then press and hold the "Flag" Button pressed. (nothing will happen)
    additional (hold the Flag-Button still pressed) press the power button, so you are finally pushing both buttons... The blue menue should appear now.


    I go to bed now... I hope you get it run..

    Yes many are right ...... but this is valid if the device is the correct rom if the device is functioning normally, but it never leaves
    I also loaded it with 510 ROM and then load and drew it ready and then not starting
    Nothing happens
    Other ideas?
    A little history
    1. device works well with "go-pall" software
    2. I want to put his "igo, garmin, sygic ........"
    3. I want to change the ROM because it is old and is unlocked
    4. change it (but incorrect)
    5. device dies
    6. what to do ........................
    well if you want, and you can help me
    please
    helpos@abv.bg

    Einmal editiert, zuletzt von helpos ()

    If you did flash your BM with the wrong ROM (510) (i.e. you obviously know the way to flash it) and your PNA doesn't show any reaction while trying to flash once more again I suppose it has been destroyed now. I don't have any ideas left which would help you.



    EDIT: ok, probably it might help if you disconnect the accu for about 15 min, but I'm not that hopeful

    Not helping the exclusion of battery "1-2 days"
    when you press the "power" processor manages power 3.3 volt and 1.7 volt
    again when pressing the "power" processor power stop
    I do not know whether replacing the flash will help?

  • Monika

    Hat das Label [GoPal bis 3.x] hinzugefügt.